SPECIFICATIONS

Battery applicable: 3.3-4.4V lithium battery

Bluetooth: Bluetooth (LE), Bluetooth 5, Bluetooth Mesh

Brand Name: Heltec Automation

Certification: RoHS,KC

Dimensions: 51.7 * 25.4* 10.7mm

Frequency: High-power version: 863-928MHz

Hardware Resource: 7*ADC1 + 2*ADC2; 7*Touch; 3*UART; 2*I2C; 2*SPI; etc.

High-concerned chemical: None

Interface: Type-C USB; SH1.25*2 Pin lithium battery interface; SH1.25*8 Pin interface; LoRa ANT(IPEX1.0); 2.4G ANT(IPEX1.0)

LoRa Chip: SX1262

MCU: ESP32-S3R2

Max. Receiving sensitivity: -137dBm@SF12 BW=125KHz

Max. TX Power: High-power version: 28 ±1 dBm

Memory: 384KB ROM; 512KB SRAM; 16KB RTC SRAM; 2MB PSRAM; 16MB Flash

Model Number: PL103665

Nominal Capacity: 3000mAh

Operating Temperature: -20 ~ 70 ℃

Origin: Mainland China

Product Name: WiFi LoRa 32(V4)

Set Type: Batteries Only

Type: Li-Ion

Wi-Fi: 802.11 b/g/n, up to 150Mbps

Note:

1.The specification of "863-928 Full Set" does not include a GPS module, and the internal space

of the shell is small, making it impossible to install a GPS module

2.The specification of "863-928 GPS Full Set" is equipped with a GPS module, and the interior

space of the shell is large enough to install the GPS moule

Please select the correct specifications when placing an order

●More detailed WiFi LoRa 32(V4) introduction-Scan&Watch for more on

  Youtube.

Heltec WiFi LoRa 32 V4 | ESP32-S3 LoRa Development Board Upgrade | Long Range

IoT Communication

Docs & Resource

Main Features

• Base on ESP32-S3R2 & SX-1262, supports Wi-Fi b/g/n, BLE, and LoRa communication.

• 2MB PSRAM and 16MB external Flash, more suitable for UI and complex system .

• High-power version with LoRa transmission power increased to 27±1dBm.

• Form factor and pin compatibility with WiFi LoRa 32 V3.

• PC casing protects the screen and integrates FPC 2.4G antenna.

• Added SH1.25-2P solar panel interface.

• Optimized lithium battery management.

• Added SH1.25-8Pin GNSS interface.

• USB Type-C interface with integrated voltage regulation, ESD protection, short-circuit protection,

       and RF isolation design.

• Low power consumption is less than 20μA.

Specifications

FAQ

1.  2.4GHz Antenna

      The default 2.4G FPC antenna is located on the side of the plastic screen bracket.

   If you wish to use an IPEX-connected 2.4G antenna, you need to remove the inductor marked as ① in

   the diagram below, and add a 0-ohm resistor (or other conductive metal or cable) at the position

   marked ② to connect to the IPEX interface.

2.  hat development methods does it support?

       ●Arduino

       ●Micro Python

       ●Platform.io

       ●Espressif IDE

    We strongly recommend using Arduino. We have complete technical support and provide complete

    LoRaWAN code for ESP32 Arduino framework.

3.  hat’s the battery socket type?

      You can find this type of socket by search “SH1.25 x 2”.

4.  Can I order a version without the OLED display?

      Of course, you can contact our sales staff and provide your ideas.

5.  Are V3 and V4 compatible?

      They are compatible in most scenarios.

      Since V4 uses the same series of chips as V3, features the same OLED, and has an almost identical

      pin layout, V3 and V4 can be used interchangeably in the majority of cases.

      However, due to the increased transmit power, the transmit power settings in some code may no

      longer correspond directly to the actual output.

6.  Failed to upload code

      Please try the following steps:

      1.Try using a different USB cable.

      2.Enter BootLoader mode. There are two methods to enter this mode:

      ●Hold down the PRG button, connect the USB-C cable, then release the PRG button.

      ●Connect the USB-C cable, hold down the PRG button, press the RST button once, then release the

        PRG button.